Individual hose record
Excavator · Caterpillar · CAT®314D LCR · Solenoid Valve
Hose repair card
Caterpillar CAT®314D LCRPipe No. 2 · Part 4I-0821
Left fitting90° elbow, American female thread, flat-face sealFITTING · 90°View real fitting photos ↗
Right fittingAmerican female thread, flat-face sealFITTING · 0°View real fitting photos ↗
RouteInstallation route — English review pending
Tap the card to enlarge it without leaving this page.
Same system
Diagram Pipe No. 1
Installation route: Installation route — English review pendingOriginal Chinese: 电磁阀(驾驶室右)~模式转换阀
Diagram Pipe No. 8
Installation route: Installation route — English review pendingOriginal Chinese: 电磁阀(回转马达右)~
Diagram Pipe No. 8
Installation route: Installation route — English review pendingOriginal Chinese: 电磁阀(驾驶室左)~电磁阀(驾驶室右)
Diagram Pipe No. 32
Installation route: Installation route — English review pendingOriginal Chinese: 蓄能器电磁阀(分配阀右)
Diagram Pipe No. 12
Installation route: Installation route — English review pendingOriginal Chinese: 电磁阀(行走踏板右)~模式转换阀
Diagram Pipe No. 3
Installation route: Installation route — English review pendingOriginal Chinese: 电磁阀(分配阀右上)~
Diagram Pipe No. 3
Installation route: Installation route — English review pendingOriginal Chinese: 电磁阀(驾驶室左)~电磁阀(驾驶室右)
Diagram Pipe No. 1
Installation route: Installation route — English review pendingOriginal Chinese: 电磁阀(行走踏板右)~模式转换阀
Workshop guide
For Caterpillar CAT®314D LCR Solenoid Valve, identify the exact model and hydraulic system on the machine first. A part number or diagram pipe number is the fastest way to narrow a replacement hose; if neither is visible, compare the installation route and the existing hose.
Check whether a listed dimension is finished assembly length, hose-only length, or cut length. These are not interchangeable. Confirm hose specification and pressure rating, then compare both ends separately: thread, sealing seat, size, angle, and orientation.
Where an installation drawing or manual figure is available, match its callout to the part number and physical route. A hydraulic circuit diagram explains connections but does not show the exact routing of a hose on the machine. Take the old hose or clear end-fitting photographs to the workshop if any dimension is missing.
Optional cross-check
The question is already written for this machine or hose. Use a tool with web search enabled; treat its answer as a starting point and verify on the machine.
I am checking hydraulic hose repair information for "4I-0821 Hydraulic Hose Replacement Specifications". Use web search and cite a source for every factual point. Compare this HoseSeek page with manufacturer manuals and reliable parts documentation: https://www.hoseseek.com/hoses/hose_e58e1c6f92341c2985278188/ HoseSeek currently shows: part number: 4I-0821; diagram pipe number: 2; installation route: Installation route — English review pending; hose specification: DN10;1SN-6;10.4Mpa; finished length in millimetres: 650; left fitting: 90° elbow, American female thread, flat-face seal; right fitting: American female thread, flat-face seal. Verify, where applicable: 1. Exact machine model and any serial-number range. 2. Hydraulic system and installation route. 3. Hose part number and diagram pipe number. 4. Finished length, hose specification, and pressure rating. 5. Both end fittings, including thread, sealing seat, size, and angle. 6. Installation-diagram position and routing. State explicitly what you could not verify. Do not infer a missing dimension or fitting. End with a short on-machine checklist for a hose repair technician.
For reference only. Confirm the actual hose before fabrication.
