Make this hose4610785
Finished length460 mm
Working pressure14 MPa
Hose specificationDN5;2层纤维-3;14MPa
Quantity1
Left fitting美制内螺纹37°内锥JIC 37° · 0°View real fitting photos ↗
Right fitting90°公制卡套式METRIC · 90°View real fitting photos ↗
Route小臂黄油管
Individual hose record
4610785 Hose Repair Specifications
Excavator · Hitachi · ZX650LC-3 · Grease Lines
Finished length460 mm
Hose repair card
Everything needed to identify and make this hose
Hitachi ZX650LC-3Pipe No. 7 · Part 4610785
Tap the card to enlarge it without leaving this page.
Repair specifications
- Part number
- 4610785
- Diagram pipe number
- 7
- Installation route
- 小臂黄油管
- Hose specification
- DN5;2层纤维-3;14MPa
- Finished length
- 460 mm
- Working pressure
- 14 MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 90°公制卡套式
- Quantity
- 1
Same system
Related Hoses
- Length
- 350 mm
- Specification
- DN5;2层纤维-3;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 90°公制卡套式
- Length
- 1,230 mm
- Specification
- DN5;2层纤维-3;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 90°公制卡套式
- Length
- 1,900 mm
- Specification
- DN5;2层纤维-3;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 90°公制卡套式
- Length
- 2,600 mm
- Specification
- DN5;2层纤维-3;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 90°公制卡套式
- Length
- 2,600 mm
- Specification
- DN5;2层纤维-3;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 90°公制卡套式
- Length
- 340 mm
- Specification
- DN5;2层纤维-3;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 公制卡套式
- Length
- 300 mm
- Specification
- DN5;2层纤维-3;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 公制卡套式
- Length
- 660 mm
- Specification
- DN5;2层纤维-3;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 公制卡套式
Workshop guide
Finding the correct hydraulic hose for Hitachi ZX650LC-3 Grease Lines
Start with the machine and route
For Hitachi ZX650LC-3 Grease Lines, identify the exact model and hydraulic system on the machine first. A part number or diagram pipe number is the fastest way to narrow a replacement hose; if neither is visible, compare the installation route and the existing hose.
Read the dimensions before cutting
Check whether a listed dimension is finished assembly length, hose-only length, or cut length. These are not interchangeable. Confirm hose specification and pressure rating, then compare both ends separately: thread, sealing seat, size, angle, and orientation.
Records to compare
- 4610785460 mm · DN5;2层纤维-3;14MPa · 小臂黄油管
Use the drawing as a location check
Where an installation drawing or manual figure is available, match its callout to the part number and physical route. A hydraulic circuit diagram explains connections but does not show the exact routing of a hose on the machine. Take the old hose or clear end-fitting photographs to the workshop if any dimension is missing.
For reference only. Confirm the actual hose before fabrication.