Make this hose4654936
Finished length650 mm
Working pressure20.5 MPa
Hose specificationDN6;1SN-4;20.5MPa
Quantity2
Left fitting美制内螺纹37°内锥JIC 37° · 0°View real fitting photos ↗
Right fitting美制内螺纹37°内锥JIC 37° · 0°View real fitting photos ↗
Route大臂销黄油管
Individual hose record
4654936 Hose Repair Specifications
Excavator · Hitachi · ZX650LC-3 · Grease Lines
Finished length650 mm
Hose repair card
Everything needed to identify and make this hose
Hitachi ZX650LC-3Pipe No. 37 · Part 4654936
Tap the card to enlarge it without leaving this page.
Repair specifications
- Part number
- 4654936
- Diagram pipe number
- 37
- Installation route
- 大臂销黄油管
- Hose specification
- DN6;1SN-4;20.5MPa
- Finished length
- 650 mm
- Working pressure
- 20.5 MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 美制内螺纹37°内锥
- Quantity
- 2
Same system
Related Hoses
- Length
- 650 mm
- Specification
- DN6;1SN-4;20.5MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 美制内螺纹37°内锥
- Length
- 1,550 mm
- Specification
- DN6;1SN-4;20.5MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 美制内螺纹37°内锥
- Length
- 550 mm
- Specification
- DN6;1SN-04;7MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 美制内螺纹37°内锥
- Length
- 500 mm
- Specification
- DN6;1SN-4;7Mpa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 美制内螺纹37°内锥
- Length
- 2,150 mm
- Specification
- DN6;2层纤维-4;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 美制内螺纹37°内锥
- Length
- 2,200 mm
- Specification
- DN6;2层纤维-4;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 美制内螺纹37°内锥
- Length
- 2,450 mm
- Specification
- DN6;2层纤维-4;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 美制内螺纹37°内锥
- Length
- 2,500 mm
- Specification
- DN6;2层纤维-04;14MPa
- Left fitting
- 美制内螺纹37°内锥
- Right fitting
- 美制内螺纹37°内锥
Workshop guide
Finding the correct hydraulic hose for Hitachi ZX650LC-3 Grease Lines
Start with the machine and route
For Hitachi ZX650LC-3 Grease Lines, identify the exact model and hydraulic system on the machine first. A part number or diagram pipe number is the fastest way to narrow a replacement hose; if neither is visible, compare the installation route and the existing hose.
Read the dimensions before cutting
Check whether a listed dimension is finished assembly length, hose-only length, or cut length. These are not interchangeable. Confirm hose specification and pressure rating, then compare both ends separately: thread, sealing seat, size, angle, and orientation.
Records to compare
- 4654936650 mm · DN6;1SN-4;20.5MPa · 大臂销黄油管
Use the drawing as a location check
Where an installation drawing or manual figure is available, match its callout to the part number and physical route. A hydraulic circuit diagram explains connections but does not show the exact routing of a hose on the machine. Take the old hose or clear end-fitting photographs to the workshop if any dimension is missing.
For reference only. Confirm the actual hose before fabrication.