Hydraulic line repair data

SANY SY235C9-I2K Hose Repair Data

Coverage details

Hoses: 2 records
Full specifications: 2 records
Systems: 1 systems
Length range: 600–680 mm

Current machine

Find a hose on this machine

Use a system name, the number on the diagram, a part number, connection point, length, hose size, or fitting.

Pipe number, part number, route, length, or fittingSearch another machine

Hose repair details

Hose Length and Fitting List

Hose record

60082689

Installation route: 回转马达—分配阀（后边）

Length: 600 mm
Specification: 19IV
Left fitting: F38.1 90°（手写接头规格）
Right fitting: F44 90°（手写接头规格）

View full repair specifications

Hose record

60082688

Installation route: 回转马达—分配阀（前边）

Length: 680 mm
Specification: 19IV
Left fitting: F38.1 H130 90°（手写接头规格）
Right fitting: F44 H130 90°（手写接头规格）

View full repair specifications

Digitized data and source sheets

SANY SY235C9-I2K Hose Data and Original Handwritten Sheets

The table is a searchable transcription of the SANY SY235C9-I2K workshop notes. The complete original handwritten sheets are shown below without cropping.

Original handwritten sheets

Complete pages are shown in their original proportions without cropping.

SANY SY235C9-I2K hydraulic hose part numbers and recorded lengths — technician notebook page 1 of 5 — **Notebook page 1 of 5**

Workshop guide

Finding the correct hydraulic hose for SANY SY235C9-I2K

Start with the machine and route

For SANY SY235C9-I2K, identify the exact model and hydraulic system on the machine first. A part number or diagram pipe number is the fastest way to narrow a replacement hose; if neither is visible, compare the installation route and the existing hose.

Read the dimensions before cutting

Check whether a listed dimension is finished assembly length, hose-only length, or cut length. These are not interchangeable. Confirm hose specification and pressure rating, then compare both ends separately: thread, sealing seat, size, angle, and orientation.

Records to compare

60082689600 mm · 19IV · 回转马达—分配阀（后边）
60082688680 mm · 19IV · 回转马达—分配阀（前边）

Use the drawing as a location check

Where an installation drawing or manual figure is available, match its callout to the part number and physical route. A hydraulic circuit diagram explains connections but does not show the exact routing of a hose on the machine. Take the old hose or clear end-fitting photographs to the workshop if any dimension is missing.

Based on current published data

Common Repair Questions

Questions appear only when a published record or linked PDF page provides the answer.

What is the hose length range for SANY SY235C9-I2K?

Based on published records with valid lengths, the range is 600–680 mm. Open the individual record to verify its installation position and both end fittings before fabrication.

Which hose specifications are common for SANY SY235C9-I2K?

The most frequent raw specifications in the current published records are: 19IV (2 records). Verify the specification together with length, pressure, and fitting details.

How can I identify the left and right hose fittings for SANY SY235C9-I2K?

Each record keeps the left and right fitting descriptions separate. Current examples: 60082689: left F38.1 90°（手写接头规格）; right F44 90°（手写接头规格）; 60082688: left F38.1 H130 90°（手写接头规格）; right F44 H130 90°（手写接头规格）. Open the exact part-number or pipe-number record; do not swap ends based on appearance alone.