Individual hose record

245-3868 Hydraulic Hose Replacement Specifications

Excavator · Caterpillar · CAT®M315F · Control Valve

Finished length960 mm

Hose repair card

Everything needed to identify and make this hose

Caterpillar CAT®M315FPipe No. 24 · Part 245-3868

Make this hose245-3868

Finished length960 mm

Working pressure42 MPa

Hose specificationDN10;6SH-6;42Mpa

Quantity1

Left fitting90° elbow, American female thread, flat-face sealFITTING · 90°View real fitting photos ↗

Right fittingAmerican female thread, flat-face sealFITTING · 0°View real fitting photos ↗

RouteInstallation route — English review pending

Tap the card to enlarge it without leaving this page.

Repair specifications

Part number: 245-3868
Diagram pipe number: 24
Installation route: Installation route — English review pendingOriginal Chinese: 分配阀前~分配阀后
Hose specification: DN10;6SH-6;42Mpa
Finished length: 960 mm
Working pressure: 42 MPa
Left fitting: 90° elbow, American female thread, flat-face sealOriginal Chinese: 90°美制内螺纹平面密封
Right fitting: American female thread, flat-face sealOriginal Chinese: 美制内螺纹平面密封
Quantity: 1

Same system

Related Hoses

Diagram Pipe No. 26

484-9236

Installation route: Control valve → hydraulic tankOriginal Chinese: 分配阀~液压油箱

Length: 680 mm
Specification: DN32;1SN-20;4.3Mpa
Left fitting: Fitting type — English review pendingOriginal Chinese: 67°法兰-轻型
Right fitting: Fitting type — English review pendingOriginal Chinese: 67°法兰-轻型

View full repair specifications

Understand and build this hose

Workshop guide

Finding the correct hydraulic hose for Caterpillar CAT®M315F Control Valve

Start with the machine and route

For Caterpillar CAT®M315F Control Valve, identify the exact model and hydraulic system on the machine first. A part number or diagram pipe number is the fastest way to narrow a replacement hose; if neither is visible, compare the installation route and the existing hose.

See all Caterpillar CAT®M315F systems

Read the dimensions before cutting

Check whether a listed dimension is finished assembly length, hose-only length, or cut length. These are not interchangeable. Confirm hose specification and pressure rating, then compare both ends separately: thread, sealing seat, size, angle, and orientation.

Records to compare

245-3868960 mm · DN10;6SH-6;42Mpa · Installation route — English review pending

Use the drawing as a location check

Where an installation drawing or manual figure is available, match its callout to the part number and physical route. A hydraulic circuit diagram explains connections but does not show the exact routing of a hose on the machine. Take the old hose or clear end-fitting photographs to the workshop if any dimension is missing.

Optional cross-check

Ask an AI search tool to check this repair data

The question is already written for this machine or hose. Use a tool with web search enabled; treat its answer as a starting point and verify on the machine.

ChatGPT Perplexity Claude Google AI Mode

See the exact question being sent

I am checking hydraulic hose repair information for "245-3868 Hydraulic Hose Replacement Specifications". Use web search and cite a source for every factual point. Compare this HoseSeek page with manufacturer manuals and reliable parts documentation: https://www.hoseseek.com/hoses/hose_affc4c4b1d3d984fa548bd46/
HoseSeek currently shows: part number: 245-3868; diagram pipe number: 24; installation route: Installation route — English review pending; hose specification: DN10;6SH-6;42Mpa; finished length in millimetres: 960; left fitting: 90° elbow, American female thread, flat-face seal; right fitting: American female thread, flat-face seal.

Verify, where applicable:
1. Exact machine model and any serial-number range.
2. Hydraulic system and installation route.
3. Hose part number and diagram pipe number.
4. Finished length, hose specification, and pressure rating.
5. Both end fittings, including thread, sealing seat, size, and angle.
6. Installation-diagram position and routing.

State explicitly what you could not verify. Do not infer a missing dimension or fitting. End with a short on-machine checklist for a hose repair technician.

For reference only. Confirm the actual hose before fabrication.